About The AquaSafe

AquaSafe is a unique wastewater treatment process with a wide spectrum of uses and users. Our turnkey wastewater treatment equipment systems fill a niche where it does not make sense to engineer an enormous wastewater system. With AquaSafe, wastewater treatment is done in one step in a single wastewater treatment equipment tank. Rarely is pre-treatment necessary. Wastewater is pumped into the tank to the appropriate volume. Vigorous mixing is initiated and then the dry powder formulation is added in correct amount (determined by our lab). After about two minutes of agitation, the mixer is shut off and flocculation and settling begins immediately. Depending on tank size, but usually within ten to thirty minutes, the floc has settled to a dense sludge, leaving clear liquid above. After decanting, clarified water, coolants or cleaners are ready to be reused. Sludge is ready for drying and disposal.

The system is easily automated and requires no skilled personnel for operation. AquaSafe is non-hazardous, easily handled and has a long shelf life. Existing systems and equipment can usually be utilized or retrofitted. Specialized wastewater treatment equipment or complete turnkey wastewater treatment systems are available 

Benefits, and Features

Benefits of AquaSafe

Economical – pennies per gallon.
Simple – one step, one additive process. no training.
Effective – captures sub-micron particles and emulsified oils.
Quick – 15 minutes process time for 30 gallon treatment.
Safe – no nasty chemicals to buy, store, or use.

Features of AquaSafe

Simple, operator-friendly design
Dual discharge valves for easy decanting and sludge removal
Designed for use in closed-loop water feed systems
Two reservoirs with engineered settling chamber

AQUASAFE is a fast, efficient, economical and easy to use wastewater treatment technology for a variety of industrial wastewaters. It provides a dense, non leachable sludge and clear water usually suitable for recycling or discharge.

How it Works: AquaSafe causes a series of chemical and physical reactions which result in contaminants being encapsulated in a developing floc, which then sinks to the bottom of the vessel. The AquaSafe wastewater treatment results in a mass that both encapsulates and removes contaminants. The clarified liquid is decanted and filtered, sludge is then filtered and collected. Drying can be accomplished with any appropriate dewatering technology. Clarified water, coolant or cleaner is recycled, dried sludge is sent to a landfill according to local regulations.What works and what does not work: AquaSafe’s unique chemistry provides a rapid and efficient encapsulation and separation in a wide spectrum of wastewaters. In most cases, it is only necessary to indentify the appropriate blend, dosage and equipment, perhaps with simple pre-treatment chemistry. However, AquaSafe will not remove certain soluble organic chemicals, sugars, starches or alcohols (including glycols.)

Waste Water Treatment Solutions

Waste Water Treatment Solutions

AquaSafe Small Economy Series
AquaSafe Large Series

AquaSafe System Specifications and Media Table

Machine Type
Treatment Capacity (GPH)
Holding Capacity (Gal.)
Voltage
Shipping Weight
Dimensions
WTS-30AJ
30
30
120/240
125
36″ X 36″ X 52″
WTS-55AJ
55
55
120/240
155
48″ X 36″ X 52″
WTS-55AJC*
55
55
120/240
155
48″ X 36″ X 52″
WTS-120 AJ
120
120
120/240
300
60″ X 36″ X 63″
WTS-150 IN-LINE
CONTINUOUS
150 GPH
N/A
475
220 -240V/3 Phase
WTS-300 IN-LINE
CONTINUOUS
300 GPH
N/A
580
220 -240V/3 Phase
WTS-5
5
0
N/A
15
18″Dia X 16″H
WTS-425
425
425
120/240
TBD
48″ X 100″ X 109″
WTS-700
700
700
230
TBD
58.75″ X Dia” X 109″H

Other Available Accessories: cartridge filters, carbon filters, resin columns, centrifuges.

Model
Description
WW-100
is an all-purpose product that works quickly and dramatically in many situations. For this reason, it is the first product to try in a demonstration or test.
WW-200
is particularly efficacious in vibratory finishing, tumbling or cleaning wastewaters. It takes a little longer to floc in, but in many cases, is an excellent choice.
WW-300
has proven to be very good in most oily water or grease situations. It needs more time to floc than the previously mentioned blends. May result in a lower pH.
WW-380
another blend to try if the others do not work well. Sometimes, under some wastewater conditions, this is a functional blend.
WW-250
a new product that works under many conditions. It takes longer to floc but often produces a superior sludge.
WW-450
slurry useful in oily water situations or with large flow rates. It can break emulsions and start to floc by itself but is best used with WW-600.
WW-400
slurry a flocculating aid and, sometimes, a treatment of first choice. It is used in lightly contaminated wastewaters or waters with suspended solids. Needs WW-600 for flocculation. If a floc from an AquaSafe treatment is a little fluffy, it sometimes does not quite settle and a drop or so of WW-400 may tighten up the floc and effect rapid settling and separation.

Startup and Installation

A sample of the wastewater will be shipped to our laboratories for analysis and treatment protocols. Based on the analysis we will recommend on of the standard AquaSafe compounds. We will work with you from initial evaluation, lab studies, field trials, and through actual operation of the completed wastewater treatment system.